Multimaze - Medium air intake

Available in Open & Closed Circuit

Available in Oil-wetted wire mesh or Dry Paper Media

Performance

Impingement principles provide up to 96% arrestment on harmful dirt particles 10 microns or larger on the oil wetted models, the dry paper models will achieve 99% arrestment on particles 5 microns or larger. Pressure drop across a clean filter element is less than .25” WG.
Depending on connection size, total loss across a complete unit is generally less than 3” WG. and is only slightly higher in the BWM type filters-silencer models.

Construction

Relatively lightweight, Multimaze filters and filter- silencers can be supported directly on the air intake. The wire mesh filter element is of crimped galvanized screen cloth which becomes progressively denser. This results in greater dirt holding capacity, thus reducing service frequency intervals. Media will not pack down or channel due to vibration. The pleated-paper element is of pleated construction and employs a protective outer wrap to prevent damage to pleats.
Optional weather hoods are available on all models.
Finish is grey enamel.

Servicing

Unscrew wing nut and remove element. Wire mesh models require washing the element in a commercial cleaning detergent. Recharge with SAE 30 oil. Allow unit to drain prior to placing back in service. The pleated paper element is usually considered a disposable. The silencer chambers of the silenced models require no attention during servicing.

 

10

Model Number: 10M10 - Dry Paper10M - Oil Wetted10MU / BWM - Silence
Maximum CFM:700
Base Size:Minimum:4''Maximum Flange: 5'' Maximum MPT: 8''
Height (Less Connection):Type M:10 3/8''Type BWM: 21 1/8''
Diameter:No Hood:10 5/8''With Hood: 14 5/8''
Approx Weight Lbs:Type M: 25Type MU & BWM: 50
Approx Weight Lbs:Add 15 for hoodElement only: 9

Attenuation

Type MU filter silencers provide attenuation in the frequency ranges where noise levels of reciprocating compressors and engines are most objectionable. The BW models with additional acoustical components, were specifically designed for installation to lobe type compressors and centrifugal blowers.

For specific information on attenuation, Sizing refer to the PDF below

12

Model Number: 12M12 - Dry Paper12M - Oil Wetted12MU / BWM - Silence
Maximum CFM:1000
Base Size:Minimum:5''Maximum Flange: 6'' Maximum MPT: 10''
Height (Less Connection):Type M:12 3/8''Type BWM: 25 1/8''
Diameter:No Hood:12 5/8''With Hood: 16 5/8''
Approx Weight Lbs:Type M: 60Type MU & BWM: 70
Approx Weight Lbs:Add 15 for hoodElement only: 11

Attenuation

Type MU filter silencers provide attenuation in the frequency ranges where noise levels of reciprocating compressors and engines are most objectionable. The BW models with additional acoustical components, were specifically designed for installation to lobe type compressors and centrifugal blowers.

For specific information on attenuation, Sizing refer to the PDF below

14

Model Number: 14M14 - Dry Paper14M - Oil Wetted14MU / BWM - Silence
Maximum CFM:1350
Base Size:Minimum:6''Maximum Flange: 8'' Maximum MPT: 12''
Height (Less Connection):Type M:14 3/8''Type BWM: 29 1/8''
Diameter:No Hood:14 5/8''With Hood: 18 5/8''
Approx Weight Lbs:Type M: 70Type MU & BWM: 85
Approx Weight Lbs:Add 25 for hoodElement only: 17

Attenuation

Type MU filter silencers provide attenuation in the frequency ranges where noise levels of reciprocating compressors and engines are most objectionable. The BW models with additional acoustical components, were specifically designed for installation to lobe type compressors and centrifugal blowers.

For specific information on attenuation, Sizing refer to the PDF below

18

Model Number: 18M18 - Dry Paper18M - Oil Wetted18MU / BWM - Silence
Maximum CFM:2250
Base Size:Minimum:8''Maximum Flange: 10'' Maximum MPT: 12''
Height (Less Connection):Type M:18 3/8''Type BWM: 37 1/8''
Diameter:No Hood:18 5/8''With Hood: 24 5/8''
Approx Weight Lbs:Type M: 90Type MU & BWM: 140
Approx Weight Lbs:Add 40 for hoodElement only: 35

Attenuation

Type MU filter silencers provide attenuation in the frequency ranges where noise levels of reciprocating compressors and engines are most objectionable. The BW models with additional acoustical components, were specifically designed for installation to lobe type compressors and centrifugal blowers.

For specific information on attenuation, Sizing refer to the PDF below

22

Model Number: 22M22 - Dry Paper22M - Oil Wetted22MU / BWM - Silence
Maximum CFM:3250
Base Size:Minimum:10''Maximum Flange: 14'' Maximum MPT: 12''
Height (Less Connection):Type M:22 3/8''Type BWM: 45 1/8''
Diameter:No Hood:22 5/8''With Hood: 32 5/8''
Approx Weight Lbs:Type M: 135Type MU & BWM: 200
Approx Weight Lbs:Add 50 for hoodElement only: 42

Attenuation

Type MU filter silencers provide attenuation in the frequency ranges where noise levels of reciprocating compressors and engines are most objectionable. The BW models with additional acoustical components, were specifically designed for installation to lobe type compressors and centrifugal blowers.

For specific information on attenuation, Sizing refer to the PDF below

225

Model Number: 225M225 - Dry Paper225M - Oil Wetted225MU / BWM - Silence
Maximum CFM:4000
Base Size:Minimum:10''Maximum Flange: 14'' Maximum MPT: 12''
Height (Less Connection):Type M:28 3/8''Type BWM: 51 1/8''
Diameter:No Hood:22 5/8''With Hood: 32 5/8''
Approx Weight Lbs:Type M: 175Type MU & BWM: 230
Approx Weight Lbs:Add 55 for hoodElement only: 53

Attenuation

Type MU filter silencers provide attenuation in the frequency ranges where noise levels of reciprocating compressors and engines are most objectionable. The BW models with additional acoustical components, were specifically designed for installation to lobe type compressors and centrifugal blowers.

For specific information on attenuation, Sizing refer to the PDF below

30

Model Number: 30M30 - Dry Paper30M - Oil Wetted30MU / BWM - Silence
Maximum CFM:6000
Base Size:Minimum:12''Maximum Flange: 22'' Maximum MPT: 12''
Height (Less Connection):Type M:30 3/8''Type BWM: 61 1/8''
Diameter:No Hood:30 5/8''With Hood: 42''
Approx Weight Lbs:Type M: 255Type MU & BWM: 375
Approx Weight Lbs:Add 75 for hoodElement only: 77

Attenuation

Type MU filter silencers provide attenuation in the frequency ranges where noise levels of reciprocating compressors and engines are most objectionable. The BW models with additional acoustical components, were specifically designed for installation to lobe type compressors and centrifugal blowers.

For specific information on attenuation, Sizing refer to the PDF below

 

 

8

Model Number: 8M8 - Dry Paper8M - Oil Wetted8MU / BWM - Silence
Maximum CFM:400
Base Size:Minimum:3''Maximum Flange: 3.5'' Maximum MPT: 6''
Height (Less Connection):Type M:8 3/8''Type BWM: 17 1/8''
Diameter:No Hood:8 5/8''With Hood: 10 5/8''
Approx Weight Lbs:Type M: 20Type MU & BWM: 35
Approx Weight Lbs:Add 10 for hoodElement only: 6

Attenuation

Type MU filter silencers provide attenuation in the frequency ranges where noise levels of reciprocating compressors and engines are most objectionable. The BW models with additional acoustical components, were specifically designed for installation to lobe type compressors and centrifugal blowers.

For specific information on attenuation, Sizing refer to the PDF below